Daikin Inverter Air Conditioner Manual

The Daikin Inverter Air Conditioner is a high-efficiency cooling and heating system featuring inverter technology for precise temperature control, energy savings, and quiet operation. It includes multiple operation modes (Cool, Heat, Dry, Fan, Auto), advanced air purification filters, Wi-Fi connectivity (on select models), timer functions, sleep mode, and comprehensive self-diagnostic features. Below are key sections for safety, features, installation, setup, operation, maintenance, and troubleshooting.

Features at a Glance

Key components: Indoor unit with LCD display, Remote Control, Outdoor unit, Air filters, Drain hose, Power cable.

Installation

Unpack and inspect contents. Installation must be performed by a qualified technician.

1. Select location: Install indoor unit on a sturdy wall, away from direct sunlight and heat sources. Outdoor unit should be placed on a stable, level surface with adequate airflow.
2. Mount indoor unit: Use mounting plate and secure with screws. Ensure level.
3. Connect refrigerant pipes: Connect copper pipes between indoor and outdoor units. Flare connections properly and check for leaks.
4. Electrical connections: Connect power cables to indoor and outdoor units according to wiring diagram. Ensure proper grounding.
5. Drain hose: Connect drain hose to indoor unit and route to appropriate drainage.
6. Vacuum and charge: Evacuate air and moisture from refrigerant lines, then charge with specified refrigerant type and amount.

WARNING! Only qualified personnel should install. Incorrect installation can cause electric shock, fire, or injury. Ensure power is disconnected during installation.

First-Time Setup

After installation, power on the unit and configure basic settings.

1. Power on: Plug in and turn on circuit breaker. Indoor unit will beep and display may light up.
2. Remote control: Insert batteries (typically 2x AAA). Point remote at indoor unit signal receiver.
3. Test operation: Press POWER on remote. Select Cool mode and set temperature to 24°C (75°F). Ensure cool air blows after a few minutes.
4. Set clock: Use remote to set current time for timer functions.
5. Wi-Fi setup (if applicable): Download Daikin app, follow in-app instructions to connect unit to your home network.

CAUTION! Do not operate if refrigerant leak is suspected. Ensure air filters are installed before use.

Specifications

• Model Series: FTXS, RXS, or similar inverter series.
• Cooling Capacity: Typically 9,000 - 24,000 BTU/h (varies by model).
• Heating Capacity: Similar range to cooling.
• Power Supply: 220-240V AC, 50/60Hz (region dependent).
• Refrigerant: R-32 or R-410A (eco-friendly).
• Indoor Noise Level: As low as 19 dB(A) in quiet mode.
• Air Flow: Multi-directional louvers for wide air distribution.
• Dimensions (Indoor): Varies by model; consult specific model label.
• Wi-Fi Standard: IEEE 802.11 b/g/n (on compatible models).
• Operating Temp. (Cooling): Outdoor: 10°C to 46°C (50°F to 115°F).
• Operating Temp. (Heating): Outdoor: -15°C to 24°C (5°F to 75°F).

Controls and Settings

Access functions via remote control or indoor unit buttons (if available).

Remote: POWER, MODE (cycles Cool/Heat/Dry/Fan/Auto), TEMP ▲/▼, FAN SPEED, SWING (louver direction), TIMER, SLEEP, ECO, POWERFUL, CLOCK, FILTER RESET, Wi-Fi (if applicable).

Basic Settings: MODE: Select operation mode. TEMP: Set desired temperature (16°C-30°C / 61°F-86°F). FAN: Choose Auto, Low, Medium, High, or Quiet. SWING: Adjust vertical/horizontal air direction. TIMER: Set On/Off timer. SLEEP: Activates sleep mode (gradually adjusts temperature). ECO: Reduces power consumption. POWERFUL: Maximum cooling/heating for 20 minutes.

Advanced Settings (via remote hold buttons): Filter reset reminder, Self-clean activation, Louver position memory, Temperature calibration, Factory reset.

Connecting to Wi-Fi

For models with Wi-Fi, connect to control via smartphone.

1. Download the "Daikin Online Controller" app from App Store or Google Play.
2. Power on the air conditioner.
3. On remote, press and hold Wi-Fi button for 3-5 seconds until indoor unit Wi-Fi indicator blinks.
4. Open app, follow setup wizard to connect unit to your 2.4 GHz Wi-Fi network.
5. Once connected, control temperature, mode, timer, and monitor energy usage remotely.

Tip: Ensure smartphone is connected to the same Wi-Fi network during setup. Reset Wi-Fi module by pressing remote Wi-Fi button for 10 seconds if connection fails.

Operation Modes

Supports multiple modes for year-round comfort.

1. Cool: Lowers room temperature. Set desired temperature and fan speed.
2. Heat: Raises room temperature. Ensure outdoor temperature is within operating range.
3. Dry: Reduces humidity while maintaining moderate cooling. Fan speed is often automatic.
4. Fan: Circulates air without cooling/heating. Choose fan speed only.
5. Auto: Unit automatically selects Cool or Heat based on room temperature.

Additional Functions: Sleep Mode: Gradually adjusts temperature over 7 hours for energy savings and comfort. Powerful Mode: Runs at maximum capacity for 20 minutes then returns to previous settings. Eco Mode: Optimizes operation for reduced energy use. Self-Clean: Run from remote to dry indoor heat exchanger and reduce mold (takes about 30-40 minutes).

WARNING! Do not use heating mode if outdoor temperature is below specified minimum. Unit may enter defrost cycle periodically during heating—this is normal.

Maintenance & Cleaning

Turn off and disconnect power before any maintenance.

1. Air Filters: Clean every 2 weeks. Open front panel, remove filters, vacuum or wash with lukewarm water and mild detergent. Dry completely before reinstalling.
2. Indoor Unit Surface: Wipe with soft, dry cloth. Do not use abrasive cleaners or water.
3. Outdoor Unit: Keep area around unit clear of leaves, dirt, and debris. Clean fins gently with soft brush if dirty.
4. Drain Pipe: Ensure drain pipe is not clogged. Pour a little water into drain pan periodically to check flow.

CAUTION! Do not use water hotter than 40°C (104°F) on filters. Do not operate without filters. Do not clean indoor unit with excessive water.

Regulatory Information

Complies with relevant safety and EMC standards (e.g., IEC, UL, CE). This product contains fluorinated greenhouse gases covered by the Kyoto Protocol. Refrigerant type and amount are stated on unit label. Do not vent refrigerant into atmosphere; recovery by certified technician required. Copyright © Daikin Industries, Ltd. All rights reserved. For support, visit www.daikin.com or contact your local Daikin dealer.

Troubleshooting

Reset: Turn off via remote, wait 1 minute, turn on. For persistent issues, disconnect power for 3 minutes then reconnect.

Service: Contact authorized Daikin service center. Do not attempt to repair refrigerant system yourself.