Daikin Inverter Split System Manual

The Daikin Inverter Split System is a high-efficiency air conditioning unit featuring inverter technology for precise temperature control, energy savings, and quiet operation. This manual covers safety precautions, installation guidelines, operation instructions, maintenance procedures, and troubleshooting for various Daikin split system models. Below are key sections for features, installation, operation, maintenance, and support.

Features at a Glance

Key components: Indoor unit with LCD display, Remote Control, Outdoor unit with inverter compressor, Air filters, Drain hose, Power cables.

Installation Guidelines

Unpack and inspect all components. Installation must be performed by qualified personnel.

1. Select location: Install indoor unit on sturdy wall, away from direct sunlight and heat sources. Outdoor unit on stable surface with proper ventilation.
2. Mount indoor unit: Use mounting plate and secure with screws.
3. Connect refrigerant pipes: Ensure proper insulation and leak-free connections.
4. Connect drain hose: Route to proper drainage location with downward slope.
5. Connect electrical wiring: Follow wiring diagram; ensure proper grounding.
6. Vacuum and charge system: Evacuate air and moisture; charge with specified refrigerant.

WARNING! Only certified technicians should install. Incorrect installation can cause injury, electric shock, or fire.

First-Time Setup

After installation, perform initial setup before operation.

1. Power on: Turn on circuit breaker and press power button on remote or indoor unit.
2. Test operation: Run in Cool mode at 25°C for 15 minutes to check cooling performance.
3. Set preferences: Adjust temperature, fan speed, and airflow direction using remote.
4. Program timer: Set daily on/off schedules if needed.
5. Check drainage: Ensure condensate water drains properly.

CAUTION! Allow system to stabilize for 10 minutes after power on. Do not switch modes rapidly.

Specifications

• Cooling Capacity: 9,000 - 24,000 BTU/h (varies by model).
• Power Supply: 220-240V AC, 50/60Hz.
• Refrigerant: R-32 or R-410A (model dependent).
• Noise Level: Indoor: 19-38 dB(A); Outdoor: 46-58 dB(A).
• Operating Range: Cooling: 18°C to 46°C outdoor; Heating: -15°C to 24°C outdoor.
• Air Flow: Multi-speed fan with adjustable direction.
• Dimensions: Indoor unit: ~800 x 285 x 200 mm; Outdoor unit: ~780 x 540 x 320 mm.
• Weight: Indoor: 8-12 kg; Outdoor: 25-40 kg.
• Energy Rating: High-efficiency inverter (5-star rating available).

Controls and Settings

Control via remote or indoor unit buttons. Remote: POWER, MODE, TEMP ▲/▼, FAN SPEED, SWING, TIMER, SLEEP, ECO, RESET.

Indoor Unit: Operation indicator, Filter indicator, Test run button (for technicians).

Mode Selection: Cool (snowflake), Heat (sun), Dry (water drop), Fan (fan icon), Auto (A). Temperature Setting: 16°C to 30°C. Fan Speed: Auto, Low, Medium, High, Turbo. Swing: Adjust vertical/horizontal louvers. Timer: Set in 0.5-hour increments up to 24 hours. Sleep: Gradually adjusts temperature over 7 hours. Eco: Optimizes performance for energy saving. Filter Reset: Press and hold for 3 seconds after cleaning filter.

Connecting to Power

Ensure proper electrical connection for safe operation.

1. Turn off main power before connecting.
2. Use dedicated circuit with correct amperage (check nameplate).
3. Connect wires according to wiring diagram (L1, L2, N, Ground).
4. Secure connections with terminal blocks.
5. Install surge protector for voltage fluctuations.

Tip: Always use copper wiring of appropriate gauge. Do not extend power cables.

Operating Modes

Select mode based on needs.

1. Cool Mode: For cooling; set desired temperature (recommended 24-26°C).
2. Heat Mode: For heating; ensure outdoor temperature above operating range.
3. Dry Mode: Reduces humidity without significant cooling.
4. Fan Mode: Circulates air without cooling/heating.
5. Auto Mode: Automatically selects Cool or Heat based on room temperature.
6. Turbo: Rapid cooling/heating at maximum fan speed.
7. Quiet: Reduces fan speed for minimal noise.

WARNING! Do not operate in Heat mode when outdoor temperature is below -15°C. Allow 3-minute delay between mode changes.

Maintenance & Cleaning

Regular maintenance ensures efficiency and longevity.

1. Air Filter: Clean every 2 weeks. Remove, wash with mild detergent, dry completely, reinstall.
2. Indoor Unit: Wipe with soft dry cloth; do not use chemicals.
3. Outdoor Unit: Keep area clear of debris; clean fins with soft brush.
4. Drainage: Check drain hose monthly for clogs.
5. Professional Service: Schedule annual maintenance by qualified technician.

CAUTION! Disconnect power before cleaning. Do not wash indoor unit with water.

Regulatory Information

Complies with safety standards: IEC 60335-1, IEC 60335-2-40. Energy efficiency compliant with local regulations. Refrigerant handling requires certified technicians. Copyright © Daikin Industries, Ltd. All rights reserved. For support, visit www.daikin.com or contact local authorized service center.

Troubleshooting

Reset: Turn off at breaker for 5 minutes, then restart.

Service: Contact authorized Daikin service center. Do not attempt repairs yourself.