daikin wired remote controller manual brc1e73

The Daikin BRC1E73 is a wired remote controller designed for use with compatible Daikin air conditioning systems. It features a clear LCD display, intuitive button interface, temperature control, mode selection (Cool, Heat, Fan, Dry, Auto), fan speed adjustment, timer functions, and system status indicators. Below are key sections for safety, features, installation, setup, operation, and troubleshooting.

1. Features at a Glance 2. Installation 3. First-Time Setup 4. Specifications 5. Controls and Settings 6. Connecting to AC System 7. Basic Operation 8. Advanced Functions 9. Care & Cleaning 10. Regulatory Information 11. Troubleshooting

Features at a Glance

Key components: LCD display with backlight, Control buttons, Connection terminal block, Mounting bracket, Status LEDs.

FeatureDescription
LCD DisplayShows temperature, mode, fan speed, timer, and system status
Mode SelectionCool, Heat, Fan, Dry, Auto operation modes
Temperature ControlAdjustable in 1°C/1°F increments
Fan Speed ControlAuto, Low, Medium, High, and Quiet settings
Timer FunctionsOn/Off timer with daily or weekly programming
Filter Sign IndicatorAlerts when air filter needs cleaning
Powerful OperationTurbo mode for rapid cooling/heating
Swing ControlAdjustable air flow direction
Connection TerminalFor wired connection to indoor unit
Child LockPrevents accidental operation changes

Installation

Unpack and inspect contents. Ensure compatibility with Daikin indoor unit.

  1. Turn off power to the air conditioning system at the circuit breaker.
  2. Select mounting location: 1.5m from floor, away from direct sunlight and heat sources.
  3. Mount bracket to wall using provided screws and wall anchors.
  4. Connect control wires to terminal block according to wiring diagram.
  5. Snap controller onto mounting bracket.
  6. Restore power and test operation.

WARNING! Installation must be performed by qualified personnel only. Incorrect wiring may damage equipment.

First-Time Setup

After installation, configure basic settings.

  1. Power on: Ensure indoor unit and controller have power.
  2. Set language: Press SET button for 5 seconds, navigate to LANGUAGE setting.
  3. Set temperature units: Choose between Celsius (°C) or Fahrenheit (°F).
  4. Set clock: Configure current time for timer functions.
  5. Test all modes: Verify Cool, Heat, Fan, Dry, and Auto operations.

CAUTION! Do not expose controller to water or excessive moisture during setup.

Specifications

Controls and Settings

Front Panel: ON/OFF, MODE, FAN, TEMP ▲/▼, TIMER, SWING, FILTER, SET buttons.

Basic Controls: ON/OFF - System power; MODE - Cycle through operation modes; TEMP ▲/▼ - Adjust temperature; FAN - Select fan speed.

Advanced Settings: Press SET for 3 seconds to access: Clock setting, Temperature unit, Filter timer reset, Child lock, System test. Timer Programming: Set daily On/Off schedules. Swing Control: Adjust vertical/horizontal air flow direction. Filter Sign: Reset after cleaning filter.

Connecting to AC System

Wired connection to compatible Daikin indoor unit.

  1. Ensure power is OFF at circuit breaker.
  2. Remove controller cover to access terminal block.
  3. Connect control wires according to wiring diagram (typically 2-5 wires).
  4. Secure wires in terminal block, ensuring no loose strands.
  5. Replace cover and restore power.

Tip: Use shielded cable for longer runs to prevent interference.

Basic Operation

Daily use procedures.

  1. Power On: Press ON/OFF button.
  2. Select Mode: Press MODE to choose Cool, Heat, Fan, Dry, or Auto.
  3. Set Temperature: Use TEMP ▲/▼ buttons.
  4. Adjust Fan Speed: Press FAN button to cycle through options.
  5. Set Timer: Press TIMER to program On/Off schedules.
  6. Adjust Air Flow: Press SWING to change direction.
  7. Power Off: Press ON/OFF to turn system off.

WARNING! Do not set temperature too low in cooling mode or too high in heating mode to prevent system strain.

Advanced Functions

Powerful Operation: Press FAN button twice in Cool/Heat mode for rapid temperature change. Quiet Operation: Select Quiet fan speed for minimal noise. Child Lock: Press and hold SET + ON/OFF for 5 seconds to enable/disable. Filter Timer Reset: Press FILTER button for 3 seconds after cleaning filter. Self-Diagnosis: Error codes display automatically when system fault detected.

Care & Cleaning

Turn off power before cleaning. Use soft, dry cloth only. Do not use chemicals or abrasives.

CAUTION! Never spray liquids directly on controller. Avoid excessive force on buttons.

Regulatory Information

Complies with relevant electrical safety standards. CE marked for European compliance. Manufactured under ISO 9001 quality standards. Copyright © Daikin Industries, Ltd. All rights reserved. For technical support, contact authorized Daikin service center or visit www.daikin.com.

Troubleshooting

SymptomPossible CauseCorrective Action
No displayPower loss, wiring issueCheck circuit breaker; verify wiring connections; ensure indoor unit has power.
Buttons not respondingChild lock enabled, system faultDisable child lock; check for error codes; restart system.
Incorrect temperature readingSensor issue, locationEnsure controller not near heat sources; contact service if persistent.
System not responding to commandsCommunication errorCheck wiring connections; restart indoor unit and controller.
Error code displayedSystem faultNote error code; consult service manual; contact Daikin service.
Timer not workingClock not set, incorrect programmingSet correct time; reprogram timer settings.

Reset: Turn off power for 5 minutes, then restore to reset controller.

Service: Contact authorized Daikin service center. Do not attempt repairs yourself.

Daikin BRC1E73 Wired Remote Controller Manual © - All Rights Reserved 2025